Rod turner motor
 

I've been looking for a rotisserie motor to make a rod turner.
Got a suggestion this AM. Use an electric can opener motor.


-- Lionel
The more I see of people, the better I like fish.

Rod turner motor
 

Go to Home Depot. They sell rotisserie motors for under $20.

--
Frank Reid
Euthanize to respond

Rod turner motor
 

Lionel F. Stevenson wrote:
I've been looking for a rotisserie motor to make a rod turner.
Got a suggestion this AM. Use an electric can opener motor.


-- Lionel
The more I see of people, the better I like fish.

If you look in the washing machine on your front poorch there is a
synchronous timing motor in it. They turn about 3 RPM and work great
for turning rods. That is for drying the varnish.There not strong
enough for winding thread ( which you don't need anyway).
They look like:
http://www.hansen-motor.com/synchindex.html

Rod turner motor
 

What's in the shed Lionel?

Microwave ovens have a useful little motor ... mains power though.

A friend powers a windscreen wiper motor mounted on a timber frame
with an old 12v dc plugpak.
(Some series resistance may be required to limit RPMs - we used,
keeping the car theme,
a 12v 5w tail light)


Steve (why can't you find a good rheostat when you need one?)

Rod turner motor
 

in article , BJ Conner
at wrote on 10/25/05 7:26 PM:


Lionel F. Stevenson wrote:
I've been looking for a rotisserie motor to make a rod turner.
Got a suggestion this AM. Use an electric can opener motor.


-- Lionel
The more I see of people, the better I like fish.

If you look in the washing machine on your front poorch there is a
synchronous timing motor in it. They turn about 3 RPM and work great
for turning rods. That is for drying the varnish.There not strong
enough for winding thread ( which you don't need anyway).
They look like:
http://www.hansen-motor.com/synchindex.html

Now, how did you know I have a washer on my front porch? How did you know I
HAVE a front porch?
:-b
-- Lionel
The more I see of people, the better I like fish.

Rod turner motor
 

Lionel F. Stevenson wrote:
in article , BJ Conner
at wrote on 10/25/05 7:26 PM:


Lionel F. Stevenson wrote:
I've been looking for a rotisserie motor to make a rod turner.
Got a suggestion this AM. Use an electric can opener motor.


-- Lionel
The more I see of people, the better I like fish.

If you look in the washing machine on your front poorch there is a
synchronous timing motor in it. They turn about 3 RPM and work great
for turning rods. That is for drying the varnish.There not strong
enough for winding thread ( which you don't need anyway).
They look like:
http://www.hansen-motor.com/synchindex.html

One of the coolest rod turners I have seen or heard of used water. A
friend used a circle of ethafoam with two plastic plates stapled to
each side. In between were small plastic cups the kind they give you
for medicine. There was a hole in the center of the ethafoam for the
rod handle.
For "bearings" he started out using some ice cube trays and scotch 33
tape around the rod shaft. He had a kitchen sink with a faucet high
enough to let the water drip into the cups and slowly turn the thing.
I have always wanted to make one just to test the stability of the
domestic tranquillity. It should be possible here in Oregon to use the
rain to run one. It doesn't get cold enough to kill all the bugs so the
guide finishings could have some interesting decorations.
Now, how did you know I have a washer on my front porch? How did you know I
HAVE a front porch?
:-b
-- Lionel
The more I see of people, the better I like fish.

Rod turner motor
 

wrote:


Steve (why can't you find a good rheostat when you need one?)

http://www.electronicsurplus.com/dictionary/cat1749.htm

Rod turner motor
 

BJ Conner wrote:

One of the coolest rod turners I have seen or heard of used water. A
friend used a circle of ethafoam with two plastic plates stapled to
each side. In between were small plastic cups the kind they give you
for medicine. There was a hole in the center of the ethafoam for the
rod handle.
For "bearings" he started out using some ice cube trays and scotch 33
tape around the rod shaft. He had a kitchen sink with a faucet high
enough to let the water drip into the cups and slowly turn the thing.
I have always wanted to make one just to test the stability of the
domestic tranquillity. It should be possible here in Oregon to use the
rain to run one. It doesn't get cold enough to kill all the bugs so the
guide finishings could have some interesting decorations.

That is one of the coolest things I've read on ROFF in a long time. It's
the solution to the challenge: Build a rod turner with available
materials for a cost of $0.00.

The essence of the solution is the source of power.

--
Cut "to the chase" for my email address.

Rod turner motor
 

That is one of the coolest things I've read on ROFF in a long time. It's
the solution to the challenge: Build a rod turner with available materials
for a cost of $0.00.

The essence of the solution is the source of power.

Steal your neighbor's washer off his front porch?
By the way, those washer timer motors are the component of choice for IED
(improvise explosive devices) timers in Iraq. Start buying 'em up and you
gonna have the FBI and BATF doing a Ruby Ridge on your butt.

--
Frank Reid
(who always knew that the Maytag repairman looked kinda shifty)
Euthanize to respond

Rod turner motor
 

;-)

Steve