January 10th, 2004, 12:57 AM
|
|
How to tell ice thickness
Well wear a pfd anyways!
"Steve Ward" wrote in message
news JHLb.38809$ts4.35865@pd7tw3no...
NEVER EVER use chest waders for ice fishing. If the ice broke you would
drown
Steve
"Dre" wrote in message
...
Chest waders?? Isn't that the worst thing you can do? If the ice breaks
and
your chest waders fill up with water then you'll sink right to the
bottom.
Dre
"Marc" wrote in message
.. .
Well be careful & wear your chest waders & PFD!
Glub! Glub!
LOL
"SC" wrote in message
...
Well, I never realised there was so much to it. Thank you both for
your
interesting and detailed replies :-)
It will be my first time ice fishing at my cottage and I intend to
go
on
16th February in Nova Scotia. I will post the group to let you know
how
I
get on.
Thanks again
ARB
"smiles" wrote in message
...
The only effective method of measuring ice thickness is by cutting
a
hole.
4 inches of solid ice is ample for someone to walk on. It will
take
a
couple of good whacks with an axe to cut through. If I can sink
the
blade
of my axe through the ice with one whack, it's a bit too thin for
my
liking.
If you plan to do the occasional fishing, you can make a cutter
out
of
a
long pole of metal and you can weld a square piece of metal to the
end.
You
sharpen the square piece and hack a hole through the ice. It will
cost
you
about 20 to 25 bucks to have one made at a welding shop. The
width
of
the
cutter should be about 2 1/2 to 3 inches wide. If you are going
to
go
ice
fishing more often and if the ice gets over 1 foot thick, an ice
auger
is
the way to go. A manual ice auger to make 8 inch diameter holes
will
cost
about 60 bucks. The cutters are very fragile. Any sand, or
getting
knocked
about will prevent any further cutting until the cutters are
sharpened.
They should be as sharp as razors. When very sharp, the auger
will
go
through the ice very quickly and easily. Occasionally, the
cutters
must
be
carefully honed otherwise you will have to buy new ones for about
20
bucks.
I carefully hone mine (keep the original angle of cut perfect) and
they
get
sharp enough to shave the hair on my forearm. There are 6 inch
diameter
augers and they are a tad less expensive. They are also fine if
you
fish
in
an area that is not really cold and the fish are not big. A
rather
large
fish can go through a 6 inch hole but when it gets really cold,
the
holes
have a tendency to freeze up and get smaller. In -15 to -25
weather,
a
6
inch hole really freezes up fast. But....cutting a hole through
ice
is
a
bit easier with a 6 inch auger. Some people who do a lot of ice
fishing,
most guides, all outfitters, use gas operated augers. They cost
about
350
dollars. When using one where there are many fishermen, you can
offer
to
cut holes for a small fee. By the end of 2 years, your machine
could
have
paid for itself. But, you will have to haul smelly gas, the extra
weight
and if the auger is not maintained, it could give you problems.
Manual
augers always start.
"SC" wrote in message
...
Hi everyone.
On the subject of ice fishing, can anyone tell me a cheap way to
measure
the
ice thickness without buying one of those ice drill things? I
have
bought
a
house by quite a shallow lake, so could I carefully step out and
hack
a
hole
with an axe and does the ice get thicker the further out you go?
Thanks a lot in advance.
ARB
|