|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
March 5th, 2005, 12:50 AM
|
|||
|
|||
Well... I got it,
Now I just gotta install it. Anyone free tomorrow for installing a trolling
motor? LOL 
|
|
#2
March 5th, 2005, 01:45 AM
|
|||
|
|||
|
Sure, right after I get back from fishing the Desert Bass tourney. I'll be
wet so have some coffee ready. Just bring it over to the house. I have all the tools we could ever need for that. I probably have all the stainless bolts we'll need to mount it, too, but it wouldn't hurt to stop by the hardware store on the way over just to be safe. I have a couple bags of 1/4 20 stainless nylocks and plenty of fender washers. -- ** Public Fishing and Boating Forums ** www.YumaBassMan.com "Charles B. Summers" wrote in message ... Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL
|
|
#3
March 5th, 2005, 02:55 AM
|
|||
|
|||
|
"Charles B. Summers" wrote in message ... Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL Sure thing Charles, bring it on up here. I have all the stainless nuts, bolts and fender washers, as well as cordless drills, wire and fish tape to get the job done. I like rigging boats. -- Steve @ OutdoorFrontiers http://www.outdoorfrontiers.com G & S Guide Service and Custom Rods http://www.herefishyfishy.com
|
|
#4
March 5th, 2005, 03:03 AM
|
|||
|
|||
|
Hmmm.... Arizona or Wisconsin? I'm sure the weather is warmed at your place.
What time is lunch? "Bob La Londe" wrote in message ... Sure, right after I get back from fishing the Desert Bass tourney. I'll be wet so have some coffee ready. Just bring it over to the house. I have all the tools we could ever need for that. I probably have all the stainless bolts we'll need to mount it, too, but it wouldn't hurt to stop by the hardware store on the way over just to be safe. I have a couple bags of 1/4 20 stainless nylocks and plenty of fender washers. -- ** Public Fishing and Boating Forums ** www.YumaBassMan.com "Charles B. Summers" wrote in message ... Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL
|
|
#5
March 5th, 2005, 03:04 AM
|
|||
|
|||
|
I can be there by 11am... you know that don't you?
"Steve @ OutdoorFrontiers" wrote in message news  "Charles B. Summers" wrote in message ... Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL Sure thing Charles, bring it on up here. I have all the stainless nuts, bolts and fender washers, as well as cordless drills, wire and fish tape to get the job done. I like rigging boats. -- Steve @ OutdoorFrontiers http://www.outdoorfrontiers.com G & S Guide Service and Custom Rods http://www.herefishyfishy.com
|
|
#6
March 5th, 2005, 03:27 AM
|
|||
|
|||
|
Weeeelllll, I could lie and tell you what the weather has been like all
week, but the truth is a storm just blew in in the last couple hours. Its raining pretty good, and the temp has dropped nearly 20 degrees in the last two hours. I'm just so looking forward to the weather tommorrow. Go see Steve, but tell him, "Fish tapes are for pikers. A fiber glass wire push pull rod is so much easier." -- ** Public Fishing and Boating Forums ** www.YumaBassMan.com "Charles B. Summers" wrote in message ... Hmmm.... Arizona or Wisconsin? I'm sure the weather is warmed at your place. What time is lunch? "Bob La Londe" wrote in message ... Sure, right after I get back from fishing the Desert Bass tourney. I'll be wet so have some coffee ready. Just bring it over to the house. I have all the tools we could ever need for that. I probably have all the stainless bolts we'll need to mount it, too, but it wouldn't hurt to stop by the hardware store on the way over just to be safe. I have a couple bags of 1/4 20 stainless nylocks and plenty of fender washers. -- ** Public Fishing and Boating Forums ** www.YumaBassMan.com "Charles B. Summers" wrote in message ... Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL
|
|
#7
March 5th, 2005, 11:52 AM
|
|||
|
|||
|
"Charles B. Summers" wrote in message ... I can be there by 11am... you know that don't you? Come on up, I'll have the coffee ready. -- Steve @ OutdoorFrontiers http://www.outdoorfrontiers.com G & S Guide Service and Custom Rods http://www.herefishyfishy.com
|
|
#8
March 5th, 2005, 03:22 PM
|
|||
|
|||
|
Charles B. Summers wrote:
Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL Charles, Which one did you get? I am putting the Minn-Kota 70lb 24v on my boat (or having it put on :-)) Chris
|
|
#9
March 5th, 2005, 04:18 PM
|
|||
|
|||
|
Same one as you. Even has the funny new "weedless" prop.
Did you order yours online? Cabelas had it for $719.99 with free shipping, and of course, no sales tax for Tennessee! "Chris Rennert" wrote in message ... Charles B. Summers wrote: Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL Charles, Which one did you get? I am putting the Minn-Kota 70lb 24v on my boat (or having it put on :-)) Chris
|
|
#10
March 12th, 2005, 01:27 AM
|
|||
|
|||
|
How many people does it take to apply duct tape Charles? You can handle it!
"Charles B. Summers" wrote in message ... Now I just gotta install it. Anyone free tomorrow for installing a trolling motor? LOL
|
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
