Stump Puller

Ok, I know some guys are going to say they don't need another piece of
equipment in the boat, and others will tell about how they use a boat cleat
or wrap the line around their rod handle, but I personally just can't see
flipping heavy braid in heavy cover without a stump puller.

Dave Willhide originally showed me one of these and strongly suggested I
make myself one five or six years ago. I was like the boat cleat and rod
handle guys until I tried it. A stump puller is basically a round smooth
piece of wood with four or five wraps of duct tape in the middle. 8-12
inches seems to be the ideal length. A broken shovel handle is ideal to cut
one from. Thick enough to do the job, and just the right size to wrap your
hand around.

http://www.yumabassman.com/gallery/d...hp?image_id=61

The idea is if you get hung up down deep where you just can't reach the hook
to undo it, and nothing else seems to work you can wrap your line around
your stump puller about six times and pull it loose or break it off.
Sometimes you will straighten out the hook. Other times you will break the
line, and once in a great while when you have a fish wrapped up in the trash
you will bring up the fish and everything he has wrapped your line around.

Absolutely do not try to do this with your hand. If you succeed in putting
enough force on it to break 65 pound or even 50 pound braided line you can
(and probably will) cut your hand to and even into the bone. Bad news. It
can mean a painful end to a good day of fishing. I posted on another
fishing group once about stump pullers and got derision from the reel handle
and boat cleat crowd. To be fair I tried both. If you think 65 pound
braided line will slice into your hand you should see what it does to a rod
handle, and then it still doesn't work well. Then I tried the boat cleat
method. If you only make a couple wraps braided line just slips right
around the cleat as you back off the boat instead of breaking it or pulling
it out. If you tie it off like dock line it doesn't slip, but the result is
still bad. It usually breaks at the cleat instead of straightening the
hook, or breaking at the hook knot like you would prefer. Might as well
have just cut the line with a knife.

Yesterday I had a tough day only managing to stick 3 of about a dozen bites
in my first two rounds of fishing a 3 round tournament. In the third round
I failed to get a good hookset on my first solid bite and my second wrapped
me up hard in the brush I was flipping. "Dang," I was thinking. "I still
just can't seem to get it together." Instead of panicing I had my partner
get out the stump puller and started steady pressure to get my line and hook
back. To my surprise the fish was still pinned. The stump puller put our
first keeper of the round in the boat, and improved both of our attitudes.

I had the fortune to have two more opportunities to put one in the livewell.
A 4.7 and a 3. Both fish were tricky, with the 4+ not cooperating about
climbing in the net. We didn't panic and we got it in the boat where the
hook promptly fell right out of the fish. The 3 wrapped itself around the
trolling motor and I had to unhook and lip the fish in the water to land it.
All three fish were problem or potential problem fish, but I credit my stump
puller with giving me back my confidence and allowing me to remain
levelheaded enough to do what I needed to do to get them in the boat. Those
three fish gave me almost 9 poounds for the round, and combined with my fish
from the previous two rounds squeaked me ahead for a first place finish
overall for the day.

To the the boat cleat & rod handle crowd I say Pbllpppppppppht!!!

Bob La Londe
www.YumaBassMan.com

"Bob La Londe" wrote in message
...
Ok, I know some guys are going to say they don't need another piece of
equipment in the boat, and others will tell about how they use a boat
cleat or wrap the line around their rod handle, but I personally just
can't see flipping heavy braid in heavy cover without a stump puller.

Dave Willhide originally showed me one of these and strongly suggested I
make myself one five or six years ago. I was like the boat cleat and rod
handle guys until I tried it. A stump puller is basically a round smooth
piece of wood with four or five wraps of duct tape in the middle. 8-12
inches seems to be the ideal length. A broken shovel handle is ideal to
cut one from. Thick enough to do the job, and just the right size to wrap
your hand around.

Willhide the guide? Yeah he showed me one, and now I have one whenver I am
on the river.

http://www.yumabassman.com/gallery/d...hp?image_id=61

Now a lot of the guys I know that fish the Delta carry them too.


snip