A Fishing forum. FishingBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » FishingBanter forum » alt.fishing & alt.flyfishing newsgroups » General Discussion
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Tips for getting a long cast?



 
 
Thread Tools Display Modes
  #1  
Old July 1st, 2008, 10:50 PM posted to alt.fishing,aus.sport.fishing,alt.fishing.minnesota,can.rec.fishing,free.uk.fishing
Logic316
external usenet poster
 
Posts: 3
Default Tips for getting a long cast?

Hi folks,
Generally speaking, what is recommended to obtain the farthest possible cast
from a spinning rod and reel? I've read in one magazine that the lighter
line you use, the less resistance you get and therefore the farther the
cast. But my dad always said that with a heavier line, you can use heavier
sinkers to get it out further. I've also read conflicting views on setting
up the reel spool and what size reel to use. I read in one fishing magazine
that keeping the spool as full of line as possible reduces the friction the
spool places on the line as it unravels during the cast (and when using my
hand to pull line off of a spool that's only filled halfway or less, this
does seem to be true). But I've seen other fisherman claim on the 'net that
the trick to a longer cast is to keep *only* as much line on the spool as
you need to make the cast and to allow sufficient line to play a fish,
because with a full spool the line will whip around in a wider circumference
and thus cause more friction against the rod guides during a cast. I've also
read that a small spool feeds out the line in a smaller circumference (and
thus places less friction against the rod guides), but one would think that
a smaller spool also causes the line to form tighter and more numerous loops
and have more "memory" which would cause more friction against the rod
guides as it's played out.
Any thoughts?

- Logic316


"If your main parachute fouls, deploy your reserve. If your reserve is also
fouled, you have the rest of your life to get it straightened out."















  #2  
Old July 9th, 2008, 03:30 AM posted to alt.fishing,aus.sport.fishing,alt.fishing.minnesota,can.rec.fishing,free.uk.fishing
Mike Dobony
external usenet poster
 
Posts: 3
Default Tips for getting a long cast?

On Tue, 1 Jul 2008 17:50:49 -0400, Logic316 wrote:

Hi folks,
Generally speaking, what is recommended to obtain the farthest possible cast
from a spinning rod and reel? I've read in one magazine that the lighter
line you use, the less resistance you get and therefore the farther the
cast. But my dad always said that with a heavier line, you can use heavier
sinkers to get it out further.


The problem here is that you need to match the line to the intended fish,
not the weight of the sinker. If you need light action for say crappie or
blue gill, especially for light nibbles, you don't want 14 lb test just to
get a heavier sinker to cast farther. Match the line and sinker to the
fish and the sensitivity needed. IMHO, if you need to get farther, get a
boat or get closer. I can get some pretty good casts off an ice jig,
splitshot, and slip bobber with a 6 1/2 foot rod and old, large
Garcia/Mitchell 300.

Can't comment on the rest.

I've also read conflicting views on setting
up the reel spool and what size reel to use. I read in one fishing magazine
that keeping the spool as full of line as possible reduces the friction the
spool places on the line as it unravels during the cast (and when using my
hand to pull line off of a spool that's only filled halfway or less, this
does seem to be true). But I've seen other fisherman claim on the 'net that
the trick to a longer cast is to keep *only* as much line on the spool as
you need to make the cast and to allow sufficient line to play a fish,
because with a full spool the line will whip around in a wider circumference
and thus cause more friction against the rod guides during a cast. I've also
read that a small spool feeds out the line in a smaller circumference (and
thus places less friction against the rod guides), but one would think that
a smaller spool also causes the line to form tighter and more numerous loops
and have more "memory" which would cause more friction against the rod
guides as it's played out.
Any thoughts?

- Logic316


Longer rod? Switch to fly fishing?


"If your main parachute fouls, deploy your reserve. If your reserve is also
fouled, you have the rest of your life to get it straightened out."

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Cast Net [email protected] Saltwater Fishing 8 June 25th, 2011 12:16 AM
Anyone Cast a 10' ? Tom Nakashima Fly Fishing 29 October 1st, 2007 02:11 PM
An Old Man and the River (Part 1) (Long. Very, very long) George Cleveland Fly Fishing 12 June 6th, 2007 04:38 PM
long cast equipment for beach? noname General Discussion 14 August 11th, 2005 02:56 AM
Looking for long casting tips John Morphet General Discussion 4 May 23rd, 2004 03:34 PM


All times are GMT +1. The time now is 09:42 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 FishingBanter.
The comments are property of their posters.