|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
October 27th, 2005, 03:46 AM
|
|||
|
|||
dubbing brush thingee...
Hi all...
Anyone have a suggestion on a dubbing brush creation tool.... saw one on the net from Czech... anyone make one in the states.... thanx ... Andy K. 
|
|
#2
October 27th, 2005, 04:09 AM
|
|||
|
|||
|
dubbing brush thingee...
"Andy" schrieb im Newsbeitrag ... Hi all... Anyone have a suggestion on a dubbing brush creation tool.... saw one on the net from Czech... anyone make one in the states.... thanx ... Andy K. http://thetwistersystem.com/ TL MC
|
|
#3
October 27th, 2005, 09:26 PM
|
|||
|
|||
|
dubbing brush thingee...
Yes try trimming a baby's tooth bush down it works great for working your
dubbing "Andy" wrote in message ... Hi all... Anyone have a suggestion on a dubbing brush creation tool.... saw one on the net from Czech... anyone make one in the states.... thanx ... Andy K.
|
|
#4
October 28th, 2005, 03:19 PM
|
|||
|
|||
|
dubbing brush thingee...
On Wed, 26 Oct 2005 19:46:41 -0700, "Andy" wrote:
Hi all... Anyone have a suggestion on a dubbing brush creation tool.... saw one on the net from Czech... anyone make one in the states.... thanx ... Andy K. Andy, I use a Nor-vise to make dubbing brushes. I have used the czech version and find that the basic problem with most of them is that as you twist the wire, there has to be some give on the other end. With the norvise I just use my hand to hold the two ends and let them twist by spinning the vise. Actually most rotary vises should work for this. The nor-vise company sells a dubbing brush table which is height adjustable. lay your wire down, apply the material, bring a wire over the top, grab the two wire ends, remove the table and spin. putting some dubbing wax on the wire helps hold everything in place during the process. Just some thoughts.... Steve Egge
|
|
#5
October 30th, 2005, 12:40 AM
|
|||
|
|||
|
dubbing brush thingee...
just glue a small piece of Velcrow(sp)(the sticky end ) to the end of a pencil, makes a great brush! also watch for our new Fly Hook Christmas Ornaments (4 inches in size)......jack at
"Andy" wrote in message ... Hi all... Anyone have a suggestion on a dubbing brush creation tool.... saw one on the net from Czech... anyone make one in the states.... thanx ... Andy K.
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Mixing dubbing... | Rodney | Fly Fishing Tying | 17 | February 25th, 2005 04:12 AM |
| Old Ligas Dubbing | [email protected] | Fly Fishing Tying | 0 | February 24th, 2005 02:52 AM |
| Dubbing material | Fish | Fly Fishing Tying | 2 | November 28th, 2004 02:51 AM |
| dubbing Q | THOMAS SCHREIBER | Fly Fishing Tying | 4 | June 5th, 2004 11:10 AM |
| Magic Tool for dubbing brush | Wayne | Fly Fishing | 9 | January 13th, 2004 10:53 PM |
Linear Mode
