Gurgler swap

Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?
--
Frank Reid
Reverse Email to reply

"Frank Reid" wrote in message
...
Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?

I've used Zap-A-Gap with success.
--
TL,
Tim
------------------------
http://css.sbcma.com/timj

"Tim J." wrote in message
...

Have foam, have legs,have hope that each of you will remember your
beginning efforts---please sign me up.

Joe McIntosh

Frank ...

I use 3M Super 77 Multipurpose Spray Adhesive
Place the foam on a newspaper ... spray the adheasive lightly from 8" or so and
then put the other piece of foam against it ... great solid flexable joint.

Steve Egge



Frank Reid wrote:

Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?

"Frank Reid" wrote in message
...
Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?
--
Frank Reid
Reverse Email to reply

I noticed that Jack Gartside is recommending getting the sticky foam sheets
(one side pre-glued). I've seen them in the craft stores. I don't tie the
double layer ones (yet) but I sometimes tie a small piece of white on top
when I'm tying off the front.

I noticed that Jack Gartside is recommending getting the sticky foam sheets
(one side pre-glued). I've seen them in the craft stores. I don't tie the
double layer ones (yet) but I sometimes tie a small piece of white on top
when I'm tying off the front.

Got some. Will try it out this week.
--
Frank Reid
Reverse Email to reply

Stan Gula wrote:

"Frank Reid" wrote in message
...

Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?
--
Frank Reid
Reverse Email to reply


I noticed that Jack Gartside is recommending getting the sticky foam sheets
(one side pre-glued). I've seen them in the craft stores. I don't tie the
double layer ones (yet) but I sometimes tie a small piece of white on top
when I'm tying off the front.

Another variation of the Gurgler foam, is some very heavy duty stuff
that a gentleman out here has been using and selling. I'm not exactly
sure what it is, but it's extremely durable, thick, and floats well.
Being it's so dense, it rides a bit lower in the water, and creates
quite a disturbance when you retrieve it. The foam is almost bulletproof.

brians

"Stan Gula" wrote...
"Frank Reid" wrote...
Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?

I noticed that Jack Gartside is recommending getting the sticky foam sheets
(one side pre-glued). I've seen them in the craft stores. I don't tie the
double layer ones (yet) but I sometimes tie a small piece of white on top
when I'm tying off the front.

That's a good idea. I noticed that pw did that (bright yellow) with his hoppers
for the DDFS: http://tinyurl.com/3x3z5. I'm going to do that from now on with
the purple gurglers I tie ( http://tinyurl.com/2y6d7 ) to make them easier to
see in the water.
--
TL,
Tim
------------------------
http://css.sbcma.com/timj

Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?

Goop will work. Comes in a tube, at Walmart, Lowe's, similar places.

vince

I am going to repost this as it is not showing on my puter
I use 3M Super 77 spray adhesive for foam It is wonderfull I sandwiched a
small rattle inbetween two pieces of foam after carving out a pocked with a
dremal tool. I used a small piece of red foam for the eyes. Try using a WD
40 spray tube for the eyes . Cut to leanth and heat with a small butane
torch Makes very neat barbell eyes. Leaving in the morning for the cicida
hatch for 4 days Life is good!
"vincent p. norris" wrote in message
...
Just tried to glue some foam together to make some cicadas (an orange
and black cicada gurgler would be a killer in a couple of weeks).
Superglue didn't work, epoxy cracked, white glue gets wet, don't have
the patience for hotmelt glue. What do you all use?

Goop will work. Comes in a tube, at Walmart, Lowe's, similar places.

vince