![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]()
Bob wrote:
I'm kickingback int he living room watching Gary fish with Bill Dance on Lake Powell, and Bill was carrying on Uhm... Bill's the one with the Tennesee hat on. That was Roland fishing with Gary H. The Kut-Tail has been around for years. It's not really a paddle tail at all. The tail is about 1/3 to 1/2 of the typical twisty tail on a worm. http://yamamoto.baits.com/order/images/7L-10.gif It has a nice, subtle action at slow speeds. There's an alternate to the "official" explanation of the worm's origin, that suggests that the originals were defects that the plastic didn't fill all the way around the tail in the mold. Gary used the rejects himself, and liked them so much they changed the mold so the tail would always pour that way. But who knows? That story could be just cabin-fever story telling. Either way, the worm works great, and the subtle action can be mimicked by trimming back the tail on any worm with a twisty type tail. I've also done it with grubs in the winter. RichZ© www.richz.com/fishing |
#2
|
|||
|
|||
![]()
On Sat, 24 Jan 2004 08:30:59 EST, RichZ wrote:
Bob wrote: I'm kickingback int he living room watching Gary fish with Bill Dance on Lake Powell, and Bill was carrying on Uhm... Bill's the one with the Tennesee hat on. That was Roland fishing with Gary H. The Kut-Tail has been around for years. It's not really a paddle tail at all. The tail is about 1/3 to 1/2 of the typical twisty tail on a worm. http://yamamoto.baits.com/order/images/7L-10.gif It has a nice, subtle action at slow speeds. There's an alternate to the "official" explanation of the worm's origin, that suggests that the originals were defects that the plastic didn't fill all the way around the tail in the mold. Gary used the rejects himself, and liked them so much they changed the mold so the tail would always pour that way. But who knows? That story could be just cabin-fever story telling. Either way, the worm works great, and the subtle action can be mimicked by trimming back the tail on any worm with a twisty type tail. I've also done it with grubs in the winter. RichZ© www.richz.com/fishing I used the cut tail last season with a whole lot of success. The one thing I would add to Rich's description is that I noticed the cut tail was heavy salted like a senko and in fact, falls like a senko. I think part of the appeal was the horizontal fall with the tail waggling. I fish it weightless on a spinning rod with 10 lb. Stren. Richard g www.bassstalkers.com |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Buck Tail Jigs | M.S. Ivey | General Discussion | 0 | February 19th, 2004 02:31 AM |
denser worm resin | Salmo Bytes | Bass Fishing | 3 | January 23rd, 2004 08:02 AM |
Denser Worm Resin II | Salmo Bytes | Bass Fishing | 0 | January 22nd, 2004 10:49 PM |
denser, heavier soft plastic (worm) resin | Salmo Bytes | General Discussion | 0 | January 22nd, 2004 08:56 PM |
Wacky Worm Rig | big fish 2003 | Bass Fishing | 2 | December 30th, 2003 05:20 PM |