![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]()
Ok... we all heard about boat handling, but there are times when you don't
have much choice, but to take chop at a bad angle. Which boat is going to be able to hold its speed and run the best in moderate conditions. Obviously when it gets bad you don't have much choice but to ignore weigh in times and other issues for the sake of safety. -- ** FREE Fishing Lures ** Weekly drawing ** Public Fishing and Boating Forums ** www.YumaBassMan.com |
#2
|
|||
|
|||
![]() "Bob La Londe" wrote in message ... Ok... we all heard about boat handling, but there are times when you don't have much choice, but to take chop at a bad angle. Which boat is going to be able to hold its speed and run the best in moderate conditions. Obviously when it gets bad you don't have much choice but to ignore weigh in times and other issues for the sake of safety. Now obviously I haven't had a chance to drive all the boats in rough water conditions, and can only base my input on personal experience. It could have been the operators, but the Rangers that I've been in were a pretty wet ride. I've heard pretty good things about Champions and Tritons. But from personal experience, my ProCraft SuperPro 190 gave me a good, dry ride for a 19' boat. I would only think that the 20 and 21' hulls would be as nice and dry. My Viper Cobra Coosa 216 (now Venom Boat Company) has been (for me) the ultimate in smooth, dry ride. It has a little deeper vee than a "standard" bassboat with a little more freeboard. The forward hull is also flared out more it seems than a standard bassboat as well which really throws the water to the sides, assisting in keeping the occupants dry. The 21'6" length, coupled with a 97" beam really means that it's stable and the length helps span big waves. The strength of the Kevlar/Coosa Composite hull means that if I can't run WFO across the tops of the waves, I can trim the nose up and let the hull take the brunt of the wave. Having the responsive and powerful Merc 250 hp ProXB with a HotFoot means that I have instant throttle response when I need to either pour it on or back off, while keeping both hands on the wheel. Having a hydraulic jackplate is helpful as well, as I can adjust the motor height for best handling. Unless the wave troughs are making it possible to bottom the prop, I'll jam that outboard just as deep in the water as I can, insuring that my prop isn't going to blow out, causing loss of control. Having the trim and jackplate controls near the steering wheel where I can control both without taking my hands off the wheel is great too. With this combination of hull, motor and control capabilities, I've been out in 7 foot waves on the Great Lakes without concern. I've run 70+ mph on Lake Okeechobee in 3 footers and been nice and dry running the tops of the waves. A lot of rough water operating is being able to read the water and know when it's safe to run fast on top, when you have to slow down and either surf the tops, nose up and crash the waves or run at angles to the waves. Unfortunately, you only get this water reading ability through experience, and that means sometimes your going to get wet spearing a wave (which is a bad thing) or thoroughly scaring the SH*&^ out of yourself. The first time I ran over 50 mph in 4 footers (for 8 miles), I think I had to send the driver's seat back in so they could fix the button hole I pinched in the seat cover! -- Steve @ OutdoorFrontiers http://www.outdoorfrontiers.com G & S Guide Service and Custom Rods http://www.herefishyfishy.com |
#3
|
|||
|
|||
![]() "Bob La Londe" wrote in message ... Ok... we all heard about boat handling, but there are times when you don't have much choice, but to take chop at a bad angle. Which boat is going to be able to hold its speed and run the best in moderate conditions. Obviously when it gets bad you don't have much choice but to ignore weigh in times and other issues for the sake of safety. Now obviously I haven't had a chance to drive all the boats in rough water conditions, and can only base my input on personal experience. It could have been the operators, but the Rangers that I've been in were a pretty wet ride. I've heard pretty good things about Champions and Tritons. But from personal experience, my ProCraft SuperPro 190 gave me a good, dry ride for a 19' boat. I would only think that the 20 and 21' hulls would be as nice and dry. My Viper Cobra Coosa 216 (now Venom Boat Company) has been (for me) the ultimate in smooth, dry ride. It has a little deeper vee than a "standard" bassboat with a little more freeboard. The forward hull is also flared out more it seems than a standard bassboat as well which really throws the water to the sides, assisting in keeping the occupants dry. The 21'6" length, coupled with a 97" beam really means that it's stable and the length helps span big waves. The strength of the Kevlar/Coosa Composite hull means that if I can't run WFO across the tops of the waves, I can trim the nose up and let the hull take the brunt of the wave. Having the responsive and powerful Merc 250 hp ProXB with a HotFoot means that I have instant throttle response when I need to either pour it on or back off, while keeping both hands on the wheel. Having a hydraulic jackplate is helpful as well, as I can adjust the motor height for best handling. Unless the wave troughs are making it possible to bottom the prop, I'll jam that outboard just as deep in the water as I can, insuring that my prop isn't going to blow out, causing loss of control. Having the trim and jackplate controls near the steering wheel where I can control both without taking my hands off the wheel is great too. With this combination of hull, motor and control capabilities, I've been out in 7 foot waves on the Great Lakes without concern. I've run 70+ mph on Lake Okeechobee in 3 footers and been nice and dry running the tops of the waves. A lot of rough water operating is being able to read the water and know when it's safe to run fast on top, when you have to slow down and either surf the tops, nose up and crash the waves or run at angles to the waves. Unfortunately, you only get this water reading ability through experience, and that means sometimes your going to get wet spearing a wave (which is a bad thing) or thoroughly scaring the SH*&^ out of yourself. The first time I ran over 50 mph in 4 footers (for 8 miles), I think I had to send the driver's seat back in so they could fix the button hole I pinched in the seat cover! -- Steve @ OutdoorFrontiers http://www.outdoorfrontiers.com G & S Guide Service and Custom Rods http://www.herefishyfishy.com |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Dry Ride - Bass Boat | go-bassn | Bass Fishing | 15 | October 23rd, 2004 12:13 AM |
Lapland Clave..... | asadi | Fly Fishing | 24 | November 10th, 2003 03:54 PM |
New Ride - She's home! | John Kerr | Bass Fishing | 3 | October 12th, 2003 03:30 AM |
New Ride | Charles B. Summers | Bass Fishing | 8 | October 1st, 2003 06:11 AM |